~2012
Original paper
１．J. Tsubaki, T. Mori, T. Konishi, A. Tsuruta, H. Mori, T. Yokoyama, S. Matsubara, “Mechanical Characterization of Spray-Dried Granules by Compression Stress-Relaxation Technique –Analysis of Compression Behavior-“, J. Ceram. Soc. Japan，107 [11], pp1093-1098 (1999)
２．J. Tsubaki, T. Mori, T. Konishi, A. Tsuruta, H. Mori, T. Yokoyama, S. Matsubara, “Mechanical Characterization of Spray-Dried Granules by Compression Stress-Relaxation Technique –Analysis of Relaxation Behavior-”，J. Ceram. Soc. Japan，107 [12], pp1183-1187 (1999)
３．T. Mori, H. Mori and J. Tsubaki, “Optimization of Experimental Conditions for the Compression and Stress Relaxation Test of Spray-Dried Granules”, J. Ceram. Soc. Japan, 110 [3], 155-158 (2002)
４．J. Tsubaki, T. Mori, H. Yamakawa, H. Mori, H. Hirose, “Hardness Measurement of Particulate Matter”, J. Soc. Powder Technol., Japan，39 [5], pp339-345 (2002)
５．J. Tsubaki, H. Yamakawa, T. Mori and H. Mori, “Optimization of Granules and Slurries for Press Forming”, J. Ceram. Soc. Japan, 110 [10], pp894-898 (2002)
６．J. Tsubaki, T. Mori, H. Yamakawa, H. Mori, H. Hirose, “Hardness Measurement of Particulate Matter –Comparison between Experimental and Estimation-”, J. Soc. Powder Technol., Japan，39 [11], pp800-805 (2002)
７．J. Tsubaki, H. Kim, T. Mori, T. Sugimoto, H. Mori, N. Sasaki, “New Evaluation Technique for Slurry Characterization by Constant Pressure Filtration”, J. Soc. Powder Technol., Japan，40 (6), 438-443 (2003)
8．T. Mori, M. Ito, T. Sugimoto, H. Mori, J. Tsubaki, “Slurry Characterization by Hydrostatic Pressure Measurement –Effect of Initial Height on Sedimentation Behavior- ”, J. Soc. Powder Technol., Japan，41 (7), 522-528 (2004)
9． H. Kim, T. Mori, J. Tsubaki, “Effect of Solid Concentration and Dispersant Dosage on Sedimentation Behavior”, J. Soc. Powder Technol., Japan, 41(9), 656-662 (2004)
10． H. Kim, T. Mori and J. Tsubaki, “Development of Slurry Characterization Method by Constant Pressure Filtration –Analysis of Cake Forming Behavior-”, J. Ceram. Soc. Japan, 113(12), 761-767 (2005)
11． T. Mori, K. Kuno, M. Ito, J. Tsubaki and T. Sakurai, “Slurry Characterization by Hydrostatic Pressure Measurement –Analysis Based on Apparent Weight Flux Ratio-” Adv. Powder Technol., 17(3), 319-332 (2006)
12． T. Mori, H. Kim, K. Ato and J. Tsubaki “Measuring Packing Fraction Distribution in Cake Filtered under Constant Pressure and Quantitative Estimation from Measured Filtrate Volume” , J. Ceram. Soc., Japan, 114(4), 318-322 (2006)
13． T. Sakurai, T. Mori and J. Tsubaki “A New Slurry Evaluation Technique by Using Ultrasonic Attenuation”, Adv. Powder Technol., 17(5), 531-541 (2006)
14． J. Tsubaki, T. Mori, Unenbat Tseveen, Ochirhuyag Bayanjarga, “Development of A Novel Slurry Condensation Method by Applying Dispersant Instead of Flocculant”, J. Soc. Powder Technol., Japan, 43(10), 731-736（2006）
15． T. Mori, T. Yamada, T. Tanaka, A. Katagiri and J. Tsubaki “Effects of Slurry Properties on the Crack Formation in Ceramics Green Sheet during Drying”, J. Ceram. Soc., Japan, 114(10), 823-828 (2006)
16． H. Satone, T. Mamiya, A. Harunari, T. Mori and J. Tsubaki “Solidification mechanism of the sediment formed by particle settling -Analysis of the final state of the sediment-“, Adv. Powder Technol., 19 (3), 293-306 (2008)
17． B. Ochirkhuyag, T. Mori, J. Tsubaki, T. Katsuoka, H. Satone, H. Choi and T. Sugimoto “Development of a High Performance Cake-less Continuous Filtration System”, Chem. Eng. Sci., 63 (21), 5274-5282 (2008)
18． H. K. Choi, B. Ochirkhuyag, J. Tsubaki, T. Mori, T. Sugimoto, J. E. Lee “The Development of a High Functional Continuous Filtration System for Sericite Powders”, Korean J. Chem. Eng., 25(5), 1165-1169 (2008)
19． J. Tsubaki, T. Katsuoka, T. Yamada, H. Satone, T. Mori and T. Sugimoto, “Development of a novel high performance continuous cake-less filtration system”, Waste Management and the Environment, 4, 761-770 (2008)
20． H. Satone, T. Mamiya, T. Mori, J. Tsubak, ” Solidification mechanism of the sediment formed by particle settling -Analysis of the formation of the solidified layer-”, Advanced Powder Technol. 20 (1), 41-47 (2009)
21． J. Tsubaki, T. Mori, U. Tseveen, O. Bayanjargal” Development of A Novel Slurry Condensation Method by Applying Dispersant Instead of Flocculant”, Advanced Powder Technol., 20 (1), 106-110 (2009)
22． T. Mori, N. Hirasawa, R. Ito and J. Tsubaki, “Ceramic Coating on Metal Substrate by Electropholetic Deposition Assisted by Sweeping Flow in Aqueous Suspension”, Key Engineering Materials, 412, 21-26 (2009)
23． T. Mori, I. Inamine, R. Wada, T. Hida, T. Kiguchi, H. Satone and J. Tsubaki, “Effects of Particle Concentration and Additive Amount of Dispersant on Adsorption Behavior of Dispersant to Alumina Particles, J. Ceram. Soc., Japan, 117 (8), 917-921 (2009)
24． K. Asai, M. Ichiyanagi, H. Satone, T. Mori, J. Tsubaki, Y. Itoh, “The Influence of Non-Newtonian Property on the Apparent Viscosity Measured by Single Cylinder Rotational Viscometer (Type-B Viscometer)”, J. Soc. Powder Technol., Japan, 46（12）、873-880（2009）
25． T. Mori, H. Satone, T. Hirata and J. Tsubaki, “Development of a novel high performance cake-less filtration system”, Water Pollution, 10, 325-332, (2010)
26． T. Kimura, K. Nakaushiro, H. Kariya, T. Mori, J. Tsubaki, “A Study on Optimizing Dough Plasticity for Manufacturing Insulators”, J. Soc. Powder Technol., Japan, 47 (8), 539-544 (2010)
27． T. Kiguchi, I. Inamine, H. Satone, T. Mori, J. Tsubaki, “Effects of Dispersant Dosage on Settling Behavior”, J. Soc. Powder Technol., Japan, 47 (9), 616-622 (2010)
28． T. Kimura, K. Nakaushiro, H. Kariya, T. Mori, J. Tsubaki, “Seasonal Changes in the Aggregate Status of Particles in Dough used in the Manufacture of Insulators”, J. Soc. Powder Technol., Japan, 47 (10), 692-696 (2010)
29． H. Ohtsuka, H. Mizutani, S. IIO, K. Asai, T. Kiguchi, H. Satone, T. Mori and J. Tsubaki, “Effects of sintering additives on dispersion properties of Al2O3 slurry containing polyacrylic acid dispersant, J. Euro. Ceram. Soc., 31 (4), 517-522 (2011)
30． T. Katsuoka, H. Satone, T. Yamada, T. Mori and J. Tsubaki, “Development of a novel high performance filtration system -Optimization of operating conditions”, Powder Technol., 207 (1-3), 154-158 (2011)
31． H. Satone, K. Nishiuma, K. Iimura, M. Suzuki, T. Mori, J. Tsubaki, “Particle Size Measurement by Hydrostatic Pressure Measurement Method –Effect of Initial Concentration”, J. Soc. Powder Technol., Japan, 48 (7), 456-463 (2011)
32． K. Asai, K. Naganawa, T. Mori, J. Tsubaki, “Direct Observation and Characterization of Particle Assembling State in Suspension”, J. Soc. Powder Technol., Japan, 48 (8), 518-525 (2011)
33． H. Satone, T. Katsuoka, K. Asai, T. Yamada, T. Mori and J. Tsubaki, “Development of a novel high performance filtration system -Application for various hardly filterable materials”, Powder Technol., 213 (1-3), 48-54 (2011)
34． T. Tanaka, K. Asai, T. Mori, J. Tsubaki, “Evaluation of Particle Assembling State in Slurries for a Cathode of Li-ion Battery”, J. Soc. Powder Technol., Japan, 48 (11), 761-767 (2011)
35． T. Kiguchi, M. Tanaka, T. Mori, J. Tsubaki, H. Satone, “Effects of Polyelectrolyte Dispersant Conformation and Magnesium Ion on Adsorption to Slurry Particles”, J. Soc. Powder Technol., Japan, 49 (2), 100-107 (2012)
36． K. Asai, K. Naganawa, T. Mori, J. Tsubaki, “Direct Observation and Characterization of Effect of Preparing Condition on Particle Assembling State in Suspension”, J. Soc. Powder Technol., Japan, 49 (3), 177-183 (2012)
37． T. Kiguchi, T. Mori, J. Tsubaki, “Adsorption and Desorption Mechanism of Carboxylate to Alumina Particles”, J. Soc. Powder Technol., Japan, 49 (4), 274-280 (2012)
38． T. Mori, Y. Hori, H. Fei, I. Inamine, K. Asai, T. Kiguchi and J. Tsubaki, “Experimental study about the agglomeration behavior in slurry prepared by adding excess polyelectrolyte dispersant”, Adv. Powder Technol., 23 (5), 661-666 (2012)
International Conference
1． Mori, A. Tsuruta, H. Mori and J. Tsubaki, “Effect of Compression Rate on the Compression and Stress Relaxation Test of Spray-Dried Granules”, 7th International Conference on Ceramic Processing Science (1999), Inuyama, Japan
2．T. Mori, A. Tsuruta, H. Mori and J. Tsubaki, “Optimization of Experimental Conditions for the Compression and Stress-Relaxation Test of Spray-Dried Granules”, First Asian Particle Technology Symposium (APT2000) (2000), Bangkok, Thailand
3．T. Mori, H. Yamakawa, H. Hirose, H. Mori and J. Tsubaki, “Measuring the Hardness of Particles by a Compression and Stress Relaxation Test”, 4th World Congress on Particle Technology (2002), Sydney, Australia
4．T. Mori, J. Tsubaki, T. Sugimoto and T. Sakurai, “Characterization of Slurry Compressibility by Different Measurement Principles”, Proceedings of The 2nd Asian Particle Technology Symposium 2003 (APT2003) volume 2, 23-28 (2003)
5．T. Mori, T. Yamada and J. Tsubaki, “Development of Slurry Characterization Method for Tape Casting Process”, The Korea-Japan International Symposium on Powder Science and Technology, 490-493, (2005), Busan, Korea
6．J. Tsubaki, B. Ochirhuyag, K. Ato, T. Mori, H. K. Choi and T. Sugimoto, “Development of a High Performance Cake-Less Continuous Filtration System”, Proceedings of International Conference & Exhibition for Filtration and Separation Technology volume1, 51-56 (2005)
7．T. Mori, K. Kuno, M. Ito and J. Tsubaki, “Slurry Characterization by Hydrostatic Pressure Measurement –Analysis Based on Mass Flux Ratio-“, 8th Japan-Australia Colloid and Interface Science Gakkai, (2005), Terrigal, Australia
8．T. Mori, B. Ochirhuyag, S. Tanaka, J. Tsubaki, H. K. Choi and T. Sugimoto, “Development of High Performance Cake-less Continuous Filtration System”, 8th Japan-Australia Colloid and Interface Science Gakkai, (2005), Terrigal, Australia
9．T Mori, T. Yamada and J. Tsubaki, “Development of Slurry Characterization Method for Tape Casting Process”, 5th World Congress on Particle Technology, (2005), Florida, U.S.A.
10．B. Ochirkhuyag, H. Choi, K. Ato, T. Mori and J. Tsubaki, “Development of a High Performance Cake-less Continuous Filtration System”, Proceedings of the ISETS05 International Symposium on Ecotopia Science, 739-740 (2005), Nagoya, Japan
11．J.Tsubaki, B.Ochirkhuyag, K.Ato, T.Mori, H.K.Choi and T.Sugimoto, “Development of a High Performance Cake-less Continuous Filtration System”CHISA 2006, Prague, Czech Republic, (2006)
12．T. Mori, T. Yamada, T. Tanaka and J. Tsubaki, “Slurry Characterization by Stress Relaxation Test for Tape Casting Process”, Proceedings of 31st International COCOA BEACH Conference & Exposition on Advanced Ceramics & Composites, (2007), Florida, U.S.A.
13．B. Ochirkhuyag, T. Katsuoka, T. Sugimoto, T. Mori and J. Tsubaki, “Development of a High Performance Cake-less Continuous Filtration System – The Effect of Filter Diameter”, Proceedings of The Third Asian Particle Technology Symposium (APT2007), vol.1, 138-145 (2007), Beijing, China
14．T. Mori, A. Ito, R. Ito and J. Tsubaki, “Fabrication of Ceramic Coatings on Metal Substrate by Electrophoretic Deposition of Aqueous Slurries”, Proceedings of The Third Asian Particle Technology Symposium (APT2007), vol.2, 650-654 (2007), Beijing, China
15．I. Inamine, T. Hida, R. Wada, T. Mori and J. Tsubaki, “Adsorption behavior of polycarboxylic acid ammonium on alumina particles”, Proceedings of The Third Asian Particle Technology Symposium (APT2007), vol.1, 18-22 (2007), Beijing, China
16．H. Satone, T. Mamiya, T. Mori and J. Tsubaki, “Solidification mechanism of the sedimentation layer formed by particle settling”, Proceedings of The Third Asian Particle Technology Symposium (APT2007), vol.1, 457-464 (2007), Beijing, China
17．T. Mori, T. Katsuoka, B. Ochirkhuyag, J. Tsubaki, T. Sugimoto and H. Choi, “Development of a novel high performance continuous cake-less filtration system”, Proceedings of 10th World Filtration Congress, vol.2, 340-344 (2008)
18．H. Satone, T. Mamiya, T. Mori, and J. Tsubaki, “Solidification Mechanism of the Sediment Formed by Particle Settling”, Abstracts of 10th International Conference on Ceramic Processing Science (ICCPS-10), P47, Inuyama, Japan (2008)
19．I. Inamine, T. Hida, K. Suzuki, T. Mori and J. Tsubaki, “Adsorption Behavior of Polyelectrolyte on Ceramic Particles”, Abstracts of 10th International Conference on Ceramic Processing Science (ICCPS-10), P63, Inuyama, Japan (2008)
20．T. Mori, N. Hirasawa, R. Ito and J. Tsubaki, ”Ceramic Coating on Metal Substrate by Electrophoretic Deposition Assisted by Sweeping Flow in Aqueous Suspension”, Abstracts of 3rd International Conference on Electrophoretic Deposition:Fundamentals and Applications, P5, Awaji Island, Japan (2008)
21．T. Mori, T. Hida, K. Suzuki, I. Inamine, T. Kiguchi, and J. Tsubaki, “Adsorption Behavior of Polyelectrolyte onto Alumina Particles and its Effect on the Particles’ Dispersion State”, Abstracts of 10th Australia-Japan Colloid and Interface Science Symposium, P200, Adelaide, Australia (2009)
22．Tsubaki, J., H. Satone, T. Katsuoka, T. Hirata and T. Mori, “Development of a High Performance Continuous Cake-less Filtration System, Abstracts of 10th Australia-Japan Colloid and Interface Science Symposium, P231, Adelaide, Australia (2009)
23．Kimura, T., K. Nakaushiro, H. Kariya, T. Mori and J. Tsubaki, “Role of moisture in dough hardness”, The Forth Asian Particle Technology Symposium (APT2009) CD-ROM (2009)
24．T. Mori, H. Satone, T. Hirata and J. Tsubaki, “Development of a novel high performance cake-less filtration system”, Water Pollution 2010 (9-11 June 2010), Intercontinental Hotel, Bucharest, Romania, 11 June 2010
25．[invited lecture] T. Mori, T. Kiguchi, J. Tsubaki, J. P. O’shea and G. V. Franks, “Evaluation of particles dispersion and flocculation in slurries containing temperature responsive polymer by hydrostatic pressure measurement”, Proceedings of The 19th Nisshin Engineering Particle Technology International Seminar, 67-76, (2010)
26．[keynote lecture] T. Mori, “Characterization of particle dispersion and flocculation in suspensions -From nano to micron particle suspensions- “, 5th Asian Particle Technology Symposium, CD-ROM, (2012)